G-700

Wood Dust Processor

A Revolutionary Dust Processor

Because of the principal contradiction between dusty air flow and filtration, traditional dust collectors are struggling with filter clogging or bad air quality. Most of the dust collectors are very loud, bulky and difficult to maintain. This has been a long-standing pain for woodworkers.

To solve this problem, the Harvey team of engineers spent

over 7 years of research and study, to develop an unprecedented Dust Collector, the Gyro Air® G-700 Wood Dust Processor. The G-700 Gyro Air® Wood Dust Processor incorporates a unique, patented technology to separate dust particles from the air and capture them before they enter the filters.The G-700 uses the new Axial Centrifugation Technology (called Gyro Air® Technology), to spin the air/dust stream up to 4,000 RPM and generate a super strong centrifugal force (over 100 times gravity) to separate the dust from the air and collect it in two dust bins hidden internally in the unit.

The G-700 collects 99.7% of the dust particles before the air reaches its HEPA filters. This not only means much less cleaning of the filters, but that the airflow and static pressure will remain much more constant during operation. In addition, the air emission cleanliness level from the filters can reach an unbeatable 0.05 mg/cubic meter (50% better than the European Standard of 0.1 mg/cubic meter). The entire extraction system is aerodynamically optimized with extraordinary running efficiency, so it can save up to 50% in energy costs.

The Gyro Air® technology and its unique aerodynamic design allow the G-700 Gyro Air® to run at an incredibly low noise level of 61 to 72 dBA, depending on which speed you run the Gyro Air ... yes, it is a variable-speed machine that allows you to adjust the airflow to suit your needs. The G-700 is powered and controlled by a SIEMENS industrial 2HP motor and SIEMENS V20 Variable Frequency Driver for 24/7 applications. In addition, the Gyro Air® G-700 is equipped with a built-in Dust-Bin monitor and a Remote Control Key. Its fully enclosed housing is short enough to fit under most benches, and it has heavy-duty casters to allow it to move as needed. The two dust bins are sealed when in use but are then easily accessed through a panel on the side of the unit, and they roll out for easy emptying (and you can use disposal bags to take out wood chips).

INSTRUCTION MANUAL-PDF DOWNLOAD

CUSTOMER TESTIMONIALS

@aaron_ludwig_woodworking

My dust collection game is about to go next level.

@aaron_ludwig_woodworking

If dust collection is on your Christmas list, give me a call to discuss the Harvey G700. I love this beast! I can save you a few bucks, which is always helpful this time of year.

@dp.woodworks

If this little beast performs half as good as it looks I’ll be a happy camper lol... Big thanks to my buddy @pj_fetscher for coming down last night and helping me out with it (and with Zacapa XO.. there still some left)

@westkentuckywoodworking

Unboxing complete and the new G700 is in its new home!

•This unique dust processor is state of the art and boasts a 0.05 micron capture rate. Basically once dust enters this machine, it never leaves, all while operating at around 70 decibels, the noise of a normal conversation

•Stay tuned for more setup, special features, piping setup videos and more highlights to come!

@threedogcarvingcompany

Couldn’t be happier with my decision to upgrade the shop dust collection system with the G700 Dust Processor by @harveyindustriesintl . It’s everything it’s marketed to be - quite, compact, well made and most all - powerful. I am very impressed with this machine.

@riddickulous_woodworks

Got these two monsters delivered today from @harveywoodworking . Only had time to unbox and move into the corner, but I can't wait till I start putting everything together and get to making some sawdust.

@Todd Zucker

I recently purchased the G700. It was damaged in transit, and Danny at Harvey was very responsive and promptly shipped out a replacement part. The machine makes a huge difference for dust collection in my garage shop, especially at the bandsaw, which went from very poor dust collection to nearly zero dust escaping the collector. Where to place the unit in the garage took some pondering due to the placement of its hose connection, but the thing fortunately rolls easily on casters. I ultimately decided to rearrange the garage and put the G700 underneath an assembly table, leaving me with a much improved woodworking setup.

@Nicholas Donlon

Customer service is fantastic. Danny and Sam spent what felt like all day helping me set up shipping receiving of my G700. They did a great job!

@Paul

Harvey has been a wonderful company to deal with. I purchased a G700 and it ended up not being the right product for me, this was completely on my part of not doing my full research. I contacted Harvey with a full understanding I would need to pay shipping and a restocking fee. I had used the machine some in testing it out, they were still willing to work with me on a return. Knowing the large hit of return financially I would take I turned to sell local. Harvey was very helpful in letting the buyer transfer warranty. All phone calls and emails with Harvey were very prompt courteous and top notch. I have started to recommend them as a company to check out when people are researching woodworking equipment and dust collection. I was sad to see the G700 go, I loved its design, it just didn't fit my specifications.

@Beth Lyons

I saw a review of Harveys table saw and got curious. I went to their site and ended up not only buying the table saw but I also got the dust processor. I worked with Samantha in customer service and she was very helpful. She was able to get me reduced shipping and a further discount because of the large order. Thanks Samantha. I am looking forward to receiving my machines and will post again after some sawdust therapy hours.