- Direct Mount Compatibility: Uses pre-aligned holes on long top bracket sides.

- Table Size: 27" x 23-1/4" x 1-3/4" (685 x 590 x 45mm)

-  Weight: 89 lbs (40.5kg) — well within 330 lb capacity.

-  Installation: Straightforward attachment with included hardware.

- Direct Mount Compatibility: Uses pre-aligned holes on long top bracket sides

- Table Size: 31-1/2" x 23-1/4" x 1-3/4" (800 x 590 x 45mm)

- Weight: 102 lbs (46.5kg) - well within 330 lb capacity

- Installation: Straightforward attachment with included hardware

Mounting Hole Pattern Options:

- Top Bracket Long (K): Multiple mounting hole configurations

- Top Bracket Short (L): Flexible positioning for various table sizes

- Custom Drilling: May require table-specific holes for optimal fit

- Mounting Hardware: M8x25 cap screws with flat and spring washers included

- Universal Fit: Accommodates most aftermarket router table systems

Custom Table Considerations:

Maximum Table Weight: 330 lbs total including router, lift, and accessories

Minimum Table Size: Large enough to overlap all four top bracket mounting points

Recommended Overhang: Table should extend beyond stand perimeter for stability

Hole Drilling Requirements: Reference top bracket hole patterns for proper spacing

Professional Installation: Recommended for complex custom configurations

General Compatibility Guidelines:

- Verify mounting hole patterns match available top bracket configurations

- Ensure table weight including all accessories remains under 330 lb capacity

- Confirm table size provides adequate overlap with stand footprint

- Check router lift and motor combination does not exceed 15A electrical capacity

- Consider table overhang for safe workpiece support beyond stand perimeter

Most commercial router tables compatible with considerations:

- May require custom drilling for mounting holes

- Verify structural integrity can handle stand's concentrated support points

- Consider additional support for extremely large table extensions

- Ensure dust collection ports remain accessible after mounting

- Maintain access to router height adjustment mechanisms

Handle Bracket Feature:

- Adjustable Positioning: Mount at any height along T-slot leg profile

- Angular Adjustment: Rotate to preferred angle for convenient access

- Router Crank Storage: Accommodates most router lift height adjustment handles

- Quick Access Design: Positioned for efficient workflow during operations

- Multiple Mounting Options: Can relocate based on operator handedness preference

The Harvey COMPASS RT-S is a universal mobile router table stand featuring parallel lifting, integrated power control, adjustable height, and high-strength aluminum alloy construction. Key features include:

- Parallel lifting mechanism with foot pedal operation for workshop mobility

- Integrated electromagnetic switch with overload protection

- Adjustable ball head feet for leveling on uneven surfaces

- 330 lbs load capacity supporting heavy cast iron router tables

- T-slot aluminum legs accommodating custom tool mounting

- Universal compatibility with Harvey RT-685/RT-800 and custom router tables

The stand transforms stationary router tables into mobile workstations while maintaining professional-grade stability during operation.

The COMPASS RT-S parallel lifting system uses a cyclic mechanism with three synchronized rollers that simultaneously raise the entire stand when the foot pedal is pressed. This provides several advantages:

- Hands-free operation allowing safe router table movement

- Automatic locking maintaining raised position during transport

- Quick-release lowering for instant stabilization

- Balanced three-point contact preventing tipping during mobility

- Minimal 0-2mm ground clearance for easy pedal activation

The system eliminates manual lifting of heavy router assemblies, reducing physical strain and improving workshop safety.

Yes, the RT-S features universal compatibility with multiple mounting configurations:

- Direct mounting for Harvey RT-685 and RT-800 using pre-aligned bracket holes

- Custom router table mounting using flexible hole patterns on top brackets

- Aftermarket router table accommodation with possible custom drilling

- Maximum capacity of 330 lbs total system weight

- Adjustable brackets accommodating various table sizes and configurations

For custom installations, reference the top bracket mounting hole pattern dimensions in the instruction manual to ensure proper fitment.

Assembly requires intermediate DIY skills and typically takes 1-2 hours to complete. The package includes:

- Complete hardware set with all required fasteners

- Professional tool kit (wrenches, hex keys, ratchet)

- Detailed instruction manual with illustrated steps

- Pre-assembled base platform and lifting mechanism

Installation involves attaching legs to base platform, mounting top brackets, installing power switch assembly, securing router table, and calibrating support feet for level. Most users successfully complete assembly following the provided instructions, though professional installation is available for complex custom configurations.

All necessary tools are included with the RT-S stand:

- 10mm ratchet wrench for efficient fastener installation

- 8-10mm open-end wrench for bracket attachment

- 13-16mm open-end wrench for larger hardware

- 1.5-8mm hex key set for various fastener types

No additional tools are required for standard assembly. A level is recommended during final height adjustment to ensure proper table calibration, though not strictly necessary for basic assembly.

Harvey router tables feature direct mounting compatibility:

1. Complete RT-S stand assembly including legs, brackets, and feet

2. Position router table on top brackets aligning side mounting holes

3. Use included M8x25 cap screws with flat and spring washers

4. Secure table through pre-aligned holes on long top bracket sides

5. Tighten all fasteners systematically ensuring even pressure

6. Verify table security before connecting power or operating router

The Harvey tables are specifically designed for RT-S compatibility, eliminating custom drilling or modification requirements.

Yes, the RT-S accommodates custom router tables with considerations:

- Reference top bracket mounting hole patterns in manual for drill locations

- Ensure custom table overlaps all four top bracket mounting points

- Verify total system weight remains under 330 lb capacity

- Use appropriate fasteners for table material and thickness

- Consider table overhang beyond stand perimeter for workpiece support

The flexible mounting configuration on top brackets provides multiple hole pattern options for various custom table designs. Some installations may require drilling mounting holes in the custom table to match bracket patterns.

The RT-S features professional electromagnetic switch control:

1. Connect power switch assembly cord to wall outlet (120V standard receptacle)

2. Plug router power cord into socket located on switch assembly

3. Ensure router power switch is in ON position (control transfers to stand)

4. Remove safety pin from green start button on switch assembly

5. Press green start button to energize router through electromagnetic switch

6. Use red stop button for immediate power shutdown

The system includes overload protection automatically tripping under excessive current draw, protecting both router and electrical system. The safety pin prevents accidental startup during maintenance or router bit changes.

The parallel lifting mechanism provides simple mobility:

1. Disconnect main power cord from wall outlet before moving

2. Press foot pedal firmly to engage three-roller system

3. Stand raises automatically and locks in elevated position

4. Move stand to desired location using rolling action

5. Press foot pedal again at destination to release rollers

6. Stand lowers gently as rollers retract and support feet contact floor

7. Verify level using ball head feet adjustment if needed

8. Reconnect power and resume operation

Always disconnect power before moving to prevent accidental router startup or cord damage during transport.

The RT-S supports 330 lbs (150kg) maximum load capacity including:

- Router table weight (Harvey RT-800 weighs 102 lbs)

- Router motor and lift system weight (typically 20-40 lbs)

- Mounted accessories including fences, guards, dust collection

- Workpiece weight during operation (minimal impact on standing load)

This capacity accommodates heavy cast iron router tables with professional router systems while maintaining stability during operation and mobility. Exceeding the weight limit compromises structural integrity and lifting mechanism function.

Height adjustment uses ball head support feet:

1. After initial assembly, rotate all four feet clockwise equal number of turns

2. Extend feet until rollers lift 0-2mm above floor surface

3. Test lifting mechanism to verify proper roller engagement

4. Place precision level on router table surface

5. Fine-tune individual feet by turning clockwise (extend) or counter-clockwise (retract)

6. Achieve level table position through incremental adjustments

7. Tighten lock nuts on each foot against support legs

8. Verify level maintained after tightening lock nuts

9. Recheck level periodically during use, particularly after moving stand

The ball head design accommodates significant floor variations while maintaining stable router table positioning.

The RT-S incorporates multiple safety systems:

- Electromagnetic switch with overload protection preventing motor damage

- Safety pin lockout preventing accidental router startup

- Automatic locking lifting mechanism securing stand during transport

- Controlled lowering function preventing sudden drops

- Stable base platform design minimizing tip-over risk

- Grounded electrical system requiring proper outlet connection

- Router power cord management reducing tripping hazards

- Red emergency stop button for immediate power disconnection

Always follow safety practices including minimum 6-inch hand distance from cutters, proper feed direction, appropriate guards, and workpiece minimum length requirements.

Routine maintenance ensures optimal performance:

Daily: Visual inspection of lifting mechanism, power switch test, dust removal, surface cleaning

Weekly: Fastener inspection, height adjustment test, lifting function verification, power cord check

Monthly: Lubrication of moving parts, T-slot cleaning, switch assembly inspection, comprehensive visual check

Quarterly: Level verification, hardware replacement if worn, deep cleaning, professional inspection consideration

Annual: Complete system overhaul, component replacement, recalibration, electrical system test

Apply light machine oil to roller shafts and appropriate grease to swing shaft mechanism monthly. The RT-S requires minimal special maintenance when used in appropriate workshop environments avoiding prolonged damp conditions.

Common lifting mechanism issues and solutions:

Problem: Pedal does not engage rollers

- Check roller ground clearance adjustment (should be 0-2mm above floor)

- Verify all foot pedal assembly fasteners are tight

- Inspect tension spring for damage or disconnection

- Ensure stand weight is not pressing rollers into floor

Problem: Stand does not lock in raised position

- Clean roller shafts and swing mechanism components

- Apply lubricant to roller shaft bearings and pivot points

- Verify automatic locking mechanism moves freely

- Check for debris interfering with locking function

Problem: Uneven lifting or tilting during raising

- Verify equal weight distribution on base platform

- Check all four support legs properly secured to base

- Confirm top brackets evenly mounted and tight

- Inspect for bent or damaged roller components

If problems persist after basic troubleshooting, contact Harvey customer service for technical support and warranty assistance.

No, the RT-S is designed for indoor workshop use only:

- Electrical components require dry environment to prevent shock hazards

- Electromagnetic switch and overload protection require moisture-free operation

- Aluminum components and steel fasteners subject to accelerated corrosion in damp conditions

- Prolonged humidity exposure degrades lubricants and moving part function

- Outdoor use voids warranty coverage

Always use RT-S in dry, well-ventilated workshop environments with adequate lighting. Avoid damp basements, unheated garages during winter, or areas with significant moisture exposure. Proper environmental conditions ensure long-term reliability and safety.

Yes, Harvey Woodworking maintains comprehensive parts support for the RT-S including:

- Lifting mechanism components (rollers, shafts, springs, pedal assembly)

- Power switch assembly and electrical components

- Support legs, top brackets, and mounting hardware

- Ball head support feet and rubber mats

- Handle brackets and accessory mounting hardware

Contact Harvey customer service for specific part numbers, availability, and ordering. The exploded view parts list in the instruction manual identifies all components with reference numbers for precise replacement part specification. Warranty coverage applies to defective parts during the one-year warranty period.

Yes, the T-slot aluminum leg design accommodates accessory mounting:

- Standard T-slot profile accepts T-bolts and mounting hardware

- Custom tool holders can attach at various heights along legs

- Dust collection hose brackets mount using T-slot system

- Additional storage brackets install without drilling legs

- Handle bracket demonstrates adjustable positioning capability

The T-slot system provides flexibility for shop-made jigs, tools, and accessories enhancing router table functionality. Use appropriate T-bolts and hardware matching slot dimensions shown in instruction manual specifications.

The adjustable handle bracket accommodates most router lift cranks:

- JessEM router lift adjustment handles

- Woodpeckers height adjustment cranks

- SawStop router lift handles

- Kreg router lift adjustment tools

- Generic crank-style height adjustment handles

Mount bracket at comfortable height along T-slot legs and adjust angle for convenient access. Position based on operator handedness preference and workflow requirements. Multiple brackets can be installed if storing various tools or working from different stand positions.

The RT-S provides integrated dust management features:

- Clear access maintained to router table dust ports after mounting

- Leg T-slots accommodate dust hose bracket mounting

- Router power cord management separates dust hoses from electrical components

- Base platform design allows dust collection cabinet installation underneath

- Open leg structure permits flexible hose routing without obstruction

Connect router table fence dust port to shop vacuum or dust collector using appropriate hose sizes. Route hoses along stand legs securing with T-slot brackets to prevent tripping hazards and maintain organized workspace.

Yes, with considerations for mounting and stability:

- Maximum weight capacity of 330 lbs includes table, router, lift, and accessories

- Table must overlap all four top bracket mounting points for secure attachment

- Consider additional table overhang for workpiece support beyond stand perimeter

- May require custom drilling in table bottom to match bracket hole patterns

- Verify table size does not interfere with lifting mechanism or support feet

- Extremely large tables may benefit from supplementary support legs at extended corners

Consult Harvey technical support for guidance on specific large table installations to ensure proper mounting security and operational stability.

Yes, Harvey Woodworking provides limited warranty coverage:

- One-year limited warranty from date of retail purchase

- Covers manufacturing defects in materials and workmanship

- Repair or replacement of defective parts during warranty period

- Contact customer service for warranty claims and assistance

Warranty excludes defects from misuse, abuse, normal wear, negligence, accidents, unauthorized repairs, modifications, or lack of maintenance. Harvey is not liable for injuries, property damage, or consequential damages from product use. Retain purchase receipt as proof of purchase date for warranty service.